501-20B Supplemental Restraint System 2014 Fiesta
Diagnosis and Testing Procedure revision date: 05/6/2013

Pinpoint Test - DTC: JJ

U0151:00

Normal Operation and Fault Conditions

The OCSM uses information contained in messages from the RCM sent on the HS-CAN .



  DTC Fault Trigger Conditions


  DTC Description Fault Trigger Conditions
U0151:00 Lost Communication with Restraints Control Module: No Sub Type Information This DTC sets if the OCSM does not receive an expected message from the RCM .


Possible Causes


PINPOINT TEST A : U0151:00
NOTE: Most faults are due to connector and/or wiring concerns. Carry out a thorough inspection and verification before proceeding with the pinpoint test.
NOTE: Only disconnect or reconnect SRS components when instructed to do so within a pinpoint test step. Failure to follow this instruction may result in incorrect diagnosis of the SRS .
NOTE: Always make sure the correct SRS component is being installed. Parts released for other vehicles may not be compatible even if they appear physically similar. Check the part number listed in the Ford parts catalog to make sure the correct component is being installed. If an incorrect SRS component is installed, Diagnostic Trouble Codes (DTCs) may set.
A1   CHECK THE COMMUNICATION NETWORK
  • Ignition ON.
  • Using a diagnostic scan tool, carry out a network test.

Does the RCM pass the network test?

Yes GO to A2
No To diagnose no communication with the RCM ,
REFER to: Communications Network (418-00 Module Communications Network, Diagnosis and Testing).


A2   CHECK THE OCSM (OCCUPANT CLASSIFICATION SYSTEM MODULE) CONTINUOUS MEMORY DIAGNOSTIC TROUBLE CODES (CMDTCS)
  • Using a diagnostic scan tool, perform OCSM self-test.
  • Using a diagnostic scan tool, clear OCSM Diagnostic Trouble Codes (DTCs).
  • Wait 10 seconds.
  • Using a diagnostic scan tool, perform OCSM self-test.

Is DTC U0151:00 retrieved again?

Yes GO to A3
No The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.


A3   RETRIEVE THE RECORDED DIAGNOSTIC TROUBLE CODES (DTCS) FROM THE RCM (RESTRAINTS CONTROL MODULE) SELF-TEST
  • Using a diagnostic scan tool, perform RCM self-test.

Is DTC U3003:16 or U3003:17 recorded?

Yes
REFER to: Pinpoint Test - DTC: FF (501-20B Supplemental Restraint System, Diagnosis and Testing).
No GO to A4


A4   RETRIEVE THE RECORDED DIAGNOSTIC TROUBLE CODES (DTCS) FROM THE OCSM (OCCUPANT CLASSIFICATION SYSTEM MODULE) SELF-TEST
  • Using a diagnostic scan tool, perform OCSM self-test.
  • Check the recorded Diagnostic Trouble Codes (DTCs) from the OCSM self-test.

Is DTC U3003:16 or U3003:17 recorded?

Yes
REFER to: Pinpoint Test - DTC: FF (501-20B Supplemental Restraint System, Diagnosis and Testing).
No GO to A5


A5   CHECK FOR DTC (DIAGNOSTIC TROUBLE CODE) U0151:00 SET IN OTHER MODULES
  • Ignition ON.
  • Using a diagnostic scan tool, perform self-test for all modules.

Is DTC U0151:00 set in the ABS module or in the APIM (if equipped)?

Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new RCM .
REFER to: Restraints Control Module (RCM) (501-20B Supplemental Restraint System, Removal and Installation).
No CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new OCS sensor.
REFER to: Occupant Classification System (OCS) Sensor (501-20B Supplemental Restraint System, Removal and Installation).





Copyright © Ford Motor Company